Buick Regal Owners & Service Manuals

Buick Regal: Alcohol/Contaminants-In-Fuel Diagnosis

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Test Description

Water contamination in the fuel system may cause driveability conditions such as hesitation, stalling, no start, or misfires in one or more cylinders. Water may collect near a single fuel injector at the lowest point in the fuel injection system and cause a misfire in that cylinder. If the fuel system is contaminated with water, inspect the fuel system components for rust or deterioration.

Ethanol concentrations of greater than 10 percent can cause driveability conditions and fuel system deterioration. Fuel with more than 10 percent ethanol could result in driveability conditions such as hesitation, lack of power, stalling, or no start. Excessive concentrations of ethanol used in vehicles not designed for it may cause fuel system corrosion, deterioration of rubber components, and fuel filter restriction.

Reference Information

Special Tool

CH 44175-A Fuel Composition Tester, if available

For equivalent regional tools, refer to Special Tools (Diagnostic Tools) and Special Tools (Mechanical Tools).

System Verification

The fuel sample should be drawn from the bottom of the tank so that any water present in the tank will be detected. The sample should be bright and clear.

  • If the sample appears cloudy, or contaminated with water, as indicated by a water layer at the bottom of the sample, perform the Particulate Contaminants in Fuel Testing Procedure.
  • If alcohol contamination is suspected, perform the Alcohol in Fuel Testing procedure.

Alcohol in Fuel Testing with Special Tool, If Available

1. Test the fuel composition using the CH 44175-A Fuel Composition Tester. Refer to the User's Manual as necessary.

2. If water appears in the fuel sample, clean the fuel system.

3. Subtract 50 from the reading on the DMM in order to obtain the percentage of alcohol in the fuel sample.

4. If the fuel sample contains more than 15 percent ethanol, add fresh, regular gasoline to the vehicle's fuel tank.

5. Test the fuel composition.

6. If testing shows the ethanol percentage is still more than 15 percent, replace the fuel in the vehicle.

Alcohol in Fuel Testing without Special Tool

1. Using a 100 ml (3.38 oz) specified cylinder with 1 ml (0.034 oz) graduation marks, fill the cylinder with fuel to the 90 ml (3.04 oz) mark.

2. Add 10 ml (0.34 oz) of water in order to bring the total fluid volume to 100 ml (3.38 oz) and install a stopper.

3. Shake the cylinder vigorously for 10 - 15 seconds.

4. Carefully loosen the stopper in order to release the pressure.

5. Re-install the stopper and shake the cylinder vigorously again for 10 - 15 seconds.

6. Put the cylinder on a level surface for approximately 5 min in order to allow adequate liquid separation. If alcohol is present in the fuel, the volume of the lower layer, which would now contain both alcohol and water, will be more than 10 ml (0.34 oz). For example, if the volume of the lower layer is increased to 15 ml (0.51 oz), this indicates at least 5 percent alcohol in the fuel.

The actual amount of alcohol may be somewhat more because this procedure does not extract all of the alcohol from the fuel.

Particulate Contaminants in Fuel Testing Procedure

1. Using an approved fuel container, draw approximately 0.5 liter (0.53 qt) of fuel.

2. Place the container on a level surface for approximately 5 min in order to allow settling of the particulate contamination. Particulate contamination will show up in various shapes and colors.

Sand will typically be identified by a white or light brown crystals. Rubber will appear as black and irregular particles.

3. Observe the fuel sample. If any physical contaminants or water are present, clean the fuel system.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

  • Fuel System Cleaning
  • Fuel Tank Draining

    READ NEXT:

     Evaporative Emission System Diagnosis

    Special Tools CH-44284-2 Fuel Flapper Door Holder EN-41413-VLV EVAP Service Port Vent Fitting GE-41415-60 Engine Induction System Leak Test Adapter/Capless Fuel Fill Adapter Operating Instructi

     Electronic Ignition System Diagnosis

    Diagnostic Instructions Perform the Diagnostic System Check prior to using this diagnostic procedure: Diagnostic System Check - Vehicle Review the description of Strategy Based Diagnosis: Strate

     Inspection/Maintenance System Check

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Displays and Gauges

    SPECIFICATIONS FASTENER SPECIFICATIONS Reusable Threaded Fastener Tightening Specifications NOTE: All fasteners listed in this table can be reused after removal. SCHEMATIC AND WIRING DIAGRAMS INSTRUMENT CLUSTER WIRING SCHEMATICS Power, Ground, Serial Data and Gauges Indicators (LGX) Indicators (L

     DTC C0293

    Diagnostic Instructions Perform the Diagnostic System Check prior to using this diagnostic procedure: Diagnostic System Check - Vehicle Review the description of Strategy Based Diagnosis: Strategy Based Diagnosis An overview of each diagnostic category can be found here: Diagnostic Proced

    © 2019-2024 Copyright www.buregal6.com