Buick Regal: Engine Coolant Fan Wiring Harness Replacement (2.0L LTG)
Removal Procedure
1. Front Bumper Fascia Center Support - Remove.
2.
.png)
Clip (2) - Remove.
3. Disconnect the electrical connector. (1).
4.
.png)
Clip (1) - Remove [2x].
5.
.png)
Clip (1) - Remove.
6. Engine Coolant Fan Electrical Connector (2) - Disconnect [2x].
7.
.png)
Clip (1) - Remove [2x].
8.
.png)
Ground Cable Nut (1) - Remove.
9. Ground Cable (2) - Remove.
10.
.png)
Clip (1, 4) - Remove [2x].
11. Electrical Connector (3) @ Air Conditioning Refrigerant Pressure Sensor (2) - Disconnect.
12.
.png)
Clip (2) - Remove.
13. Electrical Connector (1) @ Body Wiring Harness - Disconnect.
14.
.png)
Engine Coolant Fan Wiring Harness (1) - Remove.
Installation Procedure
1.
.png)
Engine Coolant Fan Wiring Harness (1) - Install.
2.
.png)
Electrical Connector (1) @ Body Wiring Harness - Connect.
3. Clip (2) - Install.
4.
.png)
Electrical Connector (3) @ Air Conditioning Refrigerant Pressure Sensor (2) - Connect.
5. Clip (1, 4) - Install [2x].
6.
.png)
Ground Cable (2) - Install.
CAUTION: Refer to Fastener Caution.
7. Ground Cable Nut (1) - Install and tighten9N.m (80 lb in).
8.
.png)
Clip (1) - Install [2x].
9.
.png)
Engine Coolant Fan Electrical Connector (2) - Connect [2x].
10. Clip (1) - Install.
11.
.png)
Clip (1) - Install [2x].
12.
.png)
Connect the electrical connector. (1).
13. Clip (2) - Install.
14. Front Bumper Fascia Center Support - Install.
READ NEXT:
Engine Coolant Fan Wiring Harness Replacement (3.6L LGX)
Removal Procedure
1. Front Bumper Fascia - Remove.
2. Headlamp- Left Side - Remove.
3.
Engine Coolant Fan Wiring Harness (1) @ Air Conditioning Refrigerant Pressure
Sensor -
Disconnect.
4. Engine
Radiator Lower Bracket Replacement - Left Side
Preliminary Procedure
Radiator Replacement (2.0L LTG) or Radiator Replacement (3.6L LGX).
Radiator Lower Bracket
Procedure
Depress the locking tab on the bracket to remove.
RADIATOR LOWER BRA
Engine Oil Cooler Inlet Pipe Replacement (3.6L LGX)
Removal Procedure
1. Drain the cooling system.
2. Oil Level Indicator Tube - Remove.
3. Raise and support the vehicle.
4.
Engine Oil Cooler Inlet Pipe Bolt (1) - Remove.
5. Hose Clamp (2) - Disen
SEE MORE:
Windows
Warning:
Never leave a child, a helpless
adult, or a pet alone in a vehicle,
especially with the windows
closed in warm or hot weather.
They can be overcome by the
extreme heat and suffer
permanent injuries or even death
from heat stroke.
The vehicle aerodynamics are
designed to improve fuel econo
Brake Pedal Position Sensor Calibration
Calibration Criteria
NOTE: Do not apply the brake pedal during the brake pedal position
sensor
calibration procedure. Any movement of the brake pedal during this
procedure will cause the calibration procedure to fail. If this occurs, the
brake pedal position sensor calibration must be repeated.
Bra
