Buick Regal Owners & Service Manuals

Buick Regal: DTC B3650

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B3650 08

High Beam Request Signal Circuit Performance - Signal Invalid

Diagnostic Fault Information

Lighting

Circuit/System Description

When the low beam is activated and the turn signal/multifunction switch is placed in the high beam position, the body control module (BCM) will receive a ground signal through the turn signal/multifunction switch signal circuit to illuminate the high beam lamps.

Conditions for Running the DTC

Low beam is ON and high beam is activated.

Conditions for Setting the DTC

The body control module (BCM) reports stuck turn signal/multifunction switch.

Action Taken When the DTC Sets

The BCM will not attempt to switch ON the high beam lamps.

Conditions for Clearing the DTC

The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

Headlights/Daytime Running Lights (DRL) Wiring Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

  • Circuit Testing
  • Connector Repairs
  • Testing for Intermittent Conditions and Poor Connections
  • Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information.

Circuit/System Verification

Ignition ON, turn the headlamp switch in the low beam position. Push/pull the turn signal/multifunction switch between the ON/OFF position. The high beam lamps should be ON/OFF as the switch is cycled.

Circuit/System Testing

1. Ignition OFF, disconnect the S78 Turn Signal/Multifunction Switch harness connector. Test for less than 5 Ω between the ground circuit terminal 3 and ground.

  • If greater then the specified value, test the ground circuit for an open/high resistance.

2. Connect the S78 Turn Signal/Multifunction Switch harness connector.

3. Disconnect the X3 harness connector at the K9 Body Control Module.

4. Connect a test lamp between B+ and the signal circuit terminal 11 X3.

5. Push/pull the S78 Turn Signal/Multifunction Switch between the high beam and OFF position.

The test lamp should turn ON and OFF as the switch is cycled.

  • If the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the S78 Turn Signal/Multifunction Switch.
  • If the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the S78 Turn Signal/Multifunction Switch.

6. If all circuits test normal, replace the K9 Body Control Module.

Component Testing

Static Test

1. Ignition OFF, disconnect the S78 Turn Signal/Multifunction Switch harness connector. S78 Turn Signal/Multifunction Switch in flash position, test for less than 5 Ω between terminal 4 and terminal 3.

  • If greater than the specified value, replace the S78 Turn Signal/Multifunction Switch.

2. S78 Turn Signal/Multifunction Switch in high beam position, test for less than 5 Ω between terminal 2 and terminal 3.

  • If greater than the specified value, replace the S78 Turn Signal/Multifunction Switch.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

  • Headlamp Switch Replacement
  • Turn Signal Switch Replacement
  • Control Module References for BCM replacement, programming and setup

    READ NEXT:

     DTC B3806

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B3881 or B3882

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B3883

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Off-Road Recovery

    The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. Follow these tips: 1. Ease off the accelerator and then, if there is nothing in the way, steer the vehicle so that it straddles the edge of the pavement. 2. Turn the steering wheel about one-eighth of a tur

     Cruise Control

    With cruise control the vehicle can maintain a speed of about 40 km/h (25 mph) or more without keeping your foot on the accelerator. Cruise control does not work at speeds below 40 km/h (25 mph). Warning: Cruise control can be dangerous where you cannot drive safely at a steady speed. Do not use cru

    © 2019-2024 Copyright www.buregal6.com