Buick Regal Owners & Service Manuals

Buick Regal: DTC B389A

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B389A

Environment Identification

For symptom byte information, refer to Symptom Byte List.

Circuit/System Description

When certain modules are programmed and configured during installation, the module learns a specific environment identifier which is unique to the vehicle. The environment identifier is used to prevent the swapping modules between vehicles. The body control module (BCM) is the keeper of the environment identifier. The Instrument Cluster, Electronic Brake Control Module, HVAC Control Module, Inflatable Restraint Sensing and Diagnostic Module, engine control module (ECM), and Steering Column Lock Module (if equipped) each learn the environment identifier during their configuration process. During vehicle operation, the BCM sends the immobilizer identifier as a challenge and each module responds to the challenge by sending the environment identifier back to the BCM. If the BCM sends an incorrect immobilizer identifier or a specific number of incorrect environment identifiers are received, vehicle starting is disabled.

Conditions for Running the DTC

Ignition is in the ACCESSORY or RUN position.

Conditions for Setting the DTC

An incorrect immobilizer identifier was broadcast by the BCM.

Action Taken When the DTC Sets

  • The security indicator in the instrument cluster will illuminate.
  • Vehicle starting will be disabled.

Conditions for Clearing the DTC

A current DTC will be cleared when the BCM broadcasts a correct immobilizer identifier.

Diagnostic Aids

If BCM programming is not completed after BCM replacement, the immobilizer identifier will not be learned. If DTC B389A sets immediately after the replacement and programming of a BCM, perform the programming procedure again.

Reference Information

Schematic Reference

Immobilizer Wiring Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEW INDEX

Master Electrical Component List

Description and Operation

Immobilizer Description and Operation

Electrical Information Reference

  • Circuit Testing
  • Connector Repairs
  • Testing for Intermittent Conditions and Poor Connections
  • Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information.

Circuit/System Verification

1. Verify DTC B389A did not set immediately following the replacement and programming of the K9 Body Control Module.

  • If the DTC set immediately after the replacement and programming of the K9 Body Control Module

The immobilizer learn procedure was not properly completed. Perform the BCM immobilizer learn using the body control module IMMO Function with Existing Transponder or Remote Key in SPS. Refer to Immobilizer System Component Programming (without BTM)Immobilizer System Component Programming (with BTM).

  • Go to next step: If the DTC did not set immediately after the replacement and programming of the K9 Body Control Module

2. Verify DTC B3902 is not set in any of the control modules listed below:

  • K20 Engine Control Module
  • K36 Inflatable Restraint Sensing and Diagnostic Module
  • K17 Electronic Brake Control Module
  • K33 HVAC Control Module
  • P16 Instrument Cluster
  • K60 Steering Column Lock Module (if equipped)
  • If DTC B3902 is set in any of the modules

Refer to DTC B3902.

  • Go to next step: If DTC B3902 is not set in any of the modules

3. Perform the K9 Body Control Module immobilizer learn using body control module IMMO Function with Existing Transponder or Remote Key in SPS. Refer to Immobilizer System Component Programming (without BTM)Immobilizer System Component Programming (with BTM).

4. Verify DTC B389A does not set after programming.

  • If the DTC sets after programming

Replace the K9 Body Control Module.

  • Go to next step: If the DTC does not set after programming

5. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for body control module replacement, programming, and setup.

    READ NEXT:

     DTC B3902

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B3924-B3928

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC B3935

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Auxiliary Audio Input Malfunction (IOB)

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Refer to Diagnostic Procedure Instructions provide an overview of each diagnostic category. Diagnosti

     Radiator Replacement (3.6L LGX)

    Removal Procedure 1. Drain the cooling system. 2. Front Bumper Fascia - Remove. 3. Hood Primary Latch Mount Panel Bracket (3) - Remove. 4. Recover the refrigerant. 5. Air Conditioning Condenser Bracket (1) - Remove. 6. Transmission Fluid Cooler Inlet and Outlet Pipe Retainer @ Engine Cooler

    © 2019-2024 Copyright www.buregal6.com