Buick Regal Owners & Service Manuals

Buick Regal: Rear Wheel Drive Shaft Replacement - Right Side

Special Tools

DT-45859 Axle Remover

Equivalent regional tools: Special Tools

Removal Procedure

1. Raise and support the vehicle.

2. Remove the right rear tire and wheel assembly.

3. With the aid of an assistant holding the brake pedal down, use a breaker bar and the proper size socket to loosen the rear wheel drive shaft nut.

4.

Wheel Drive Shafts

Rear Wheel Drive Shaft Nut(1) - Remove and DISCARD.

5.

Wheel Drive Shafts

Using the DT-45859 Axle Remover (1), separate the rear wheel drive shaft from the rear wheel bearing and hub assembly.

6. Rear Suspension Knuckle - Remove.

7.

Wheel Drive Shafts

Use a suitable flat bladed tool (1) to separate the rear wheel drive shaft (2) from the differential carrier assembly.

8.

Wheel Drive Shafts

Rear Wheel Drive Shaft(1) - Remove.

9.

Wheel Drive Shafts

Rear Wheel Drive Shaft Retaining Ring(1) - Remove and DISCARD.

10. Wheel Drive Shaft O-Ring(2)@Wheel Drive Shaft - Remove and DISCARD.

Installation Procedure

1.

Wheel Drive Shafts

Wheel Drive Shaft O-Ring(2) - Install NEW.

2. Rear Wheel Drive Shaft Retaining Ring(1) - Install NEW.

3.

Wheel Drive Shafts

Rear Wheel Drive Shaft(1) - Install.

4.

Wheel Drive Shafts

Install the rear wheel drive shaft (1) until it is fully seated into the differential carrier assembly (2).

5. Rear Suspension Knuckle - Install.

6.

Wheel Drive Shafts

CAUTION: This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component.
Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.

CAUTION: Fastener Caution.

Rear Wheel Drive Shaft Nut(1) - Install NEW and tighten

  1. First Pass: 150 N.m (111 lb ft)
  2. Second Pass: Loosen 45 degrees
  3. Final Pass: 250 N.m (199 lb ft)

7. Install the right rear tire and wheel assembly.

8. Remove the support and lower the vehicle.

    READ NEXT:

     Front Wheel Drive Shaft Inner Joint and Boot Replacement

    Special Tools J-42572 Drive Shaft Seal Clamp Pliers Disassembly Procedure 1. Front Wheel Drive Half Shaft - Remove. Front Wheel Drive Half Shaft Replacement - Left Side Front Wheel Drive Half Shaft

     Rear Wheel Drive Shaft Inner Joint and Boot Replacement

    Special Tools J-42572 Drive Shaft Seal Clamp Pliers Disassembly Procedure 1. Rear Wheel Drive Shaft - Remove Rear Wheel Drive Shaft Replacement - Left Side Rear Wheel Drive Shaft Replacement - Righ

     Front Wheel Drive Shaft Outer Joint and Boot Replacement

    Special Tools J-42572 Drive Shaft Seal Clamp Pliers Disassembly Procedure 1. Front Wheel Drive Half Shaft - Remove Front Wheel Drive Half Shaft Replacement - Left Side Front Wheel Drive Half Shaft

    SEE MORE:

     DTC B390C

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptor DT

     Repair Instructions

    Tire Pressure Indicator Sensor Replacement Removal Procedure 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle. 2. Remove the tire and wheel assembly. 3. Dismount the tire from the rim. 4. NOTE: Never fit the tire pressure indicator sensor on unapproved wheel r

    © 2019-2024 Copyright www.buregal6.com