Buick Regal: Special Tools and Equipment
SPECIAL TOOLS
DT-45866
J-45866
Input Shaft Seal Installer
.png)
EN-8062
J-8062
KM-348
Valve Spring Compressor - Head Off
.png)
EN-8087
J-8087
Cylinder Bore Gauge
.png)
EN-21867-850
J-21867-850
KM-498-B
KM-6106
83 93 852
Oil Pressure Gauge Adapter
.png)
EN-22738-B
GE-22738-B
J-22738-B
J-9666
Valve Spring Tester
.png)
EN-23951
J-23951
Valve Manometer
.png)
EN-28410
J-28410
Gasket Remover
.png)
EN-28467-34
J-28467-34
Lift Hook Wing Nut and Washer
.png)
EN-28467-518
J-28467-518
Engine Support Adapter - Main Support Beam
.png)
EN-34115
J-34115
Sprocket Bearing Installer
.png)
EN-35667-A
J-35667-A
Cylinder Head Leakdown Tester
.png)
EN-36017
J-36017
KM-840 - Removal
KM-6152 - Installation
Valve Seal Remover
.png)
EN-36462-A
J-36462-A
Engine Support Adapter Leg Set
.png)
EN-36857
J-36857
Engine Lift Bracket
.png)
EN-38188
J-38188
Cylinder Head Broken Bolt Extractor Kit
.png)
EN-39358
J-39358
83 94 785
Spark Plug Socket
.png)
EN-41816
EN-51577
J-41816
Crankshaft Balancer Remover
.png)
EN-41816-2
J-41816-2
Crankshaft End Protector
.png)
EN-42385-700
J-42385-700
High Feature Thread Repair Kit
.png)
EN-42385-850
J-42385-850
Thread Repair Kit
.png)
EN-42385-880
Head Bolt Thread Repair Adapter Kit
.png)
EN-43405-1
J-43405-1
Engine Support Fixture Adapter - Passenger Side
.png)
EN-43405-2
J-43405-2
Engine Support Fixture Adapter - Driver Side
.png)
EN-43953
J-43953
Piston Ring Compressor - 86 mm
.png)
EN-43963
J-43963
KM-6149
Valve Spring Compressor (off car)
.png)
EN-43966-1
J-43966-1
Connecting Rod Guides
.png)
EN-45025
J-45025
Belt Tensioner Wrench
.png)
EN-45059
J-45059
Angle Meter
.png)
EN-45299
J-45299
Engine Pre-Luber
.png)
EN-46116
Valve Stem Seal Remover
.png)
EN-46745
J-43654
Piston Pin Clip Remover/Installer
.png)
EN-46745-4
Piston Pin Clip Remover/Installer Adapter
.png)
EN-47836
J-47836
Ring Compressor - 88 mm
.png)
EN-47909
Injector Bore and Sleeve Cleaning Kit
.png)
EN-48034
Crankshaft Balancer Installer
.png)
EN-49245
Injector Seal Installer and Sizer
.png)
EN-49248
Fuel Rail Assembly Remover
.png)
EN-50656
Timing Chain Retention Tool Kit
.png)
EN-50717
Valve Spring Compressor
.png)
EN-50717-10
Valve Spring Compressor Adapter
.png)
EN-50790
High Pressure Fuel Pump Installation Alignment Gauge
.png)
EN-50791
Fuel Injector Nozzle Installer - to Rail
.png)
EN-50793
Camshaft Actuator Locking Tool
.png)
EN-50820
Front Crankshaft Seal Installer
.png)
EN-50837
Timing Chain Tensioner Retraction Tool
.png)
EN-50956
Tamper Proof Drive Bit
.png)
EN-51105
Injector Seal Installer
.png)
EN-51380
Seal Installer
.png)
EN-51577
Balancer Holder and Remover
.png)
EN-51749
Compression Gauge Tester Kit
EN-51760
EN-50792
Flywheel Holder
EN-51768
Engine Support Fixture Adapter Bolts M8
EN-52059
Engine Support Fixture Adapter Bolts M10
GE-7872
J-7872
Magnetic Base Dial Indicator Set
GE-21867-A
J-21867-A
Oil Pressure Gauge Kit
GE-42220
J-28428-E
J-42220
Universal 12V Leak Detection Lamp
READ NEXT:
Camshaft Actuator System Description
Circuit/System Description
The camshaft position actuator solenoid valve - Intake and camshaft position
actuator solenoid valve -
exhaust system enables the engine control module (ECM) to change cams
SEE MORE:
DTC B390C
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
Diagnostic Procedure Instructions provides an overview of each
diagnostic category.
DTC Descriptor
DT
Engine Block Assemble
1.
Install the piston oil nozzle assemblies (2), if equipped.
CAUTION: Refer to Fastener Caution.
2. Install the piston oil nozzle bolts (1) and tighten to 10 N.m (89 lb in).
3.
Lubricate the crankshaft position sensor O-ring with engine oil. Refer to
Adhesives, Fluids, Lubricants, and
Sealers.
