Buick Regal: Electronic Suspension Control Module Replacement
Removal Procedure
1. Active Safety Control Module@Left Side - Remove.
2.
.png)
Remove the electronic suspension control module (2) by releasing the tab as indicated on the electronic suspension control module bracket (1).
3.
.png)
Electrical Connector(1)@Electronic Suspension Control Module(2) - Disconnect.
4. Electronic Suspension Control Module(2) - Remove.
Installation Procedure
1.
.png)
Electronic Suspension Control Module(2) - Install.
2. Electrical Connector(1)@Electronic Suspension Control Module - (2)Connect.
3.
.png)
Install the electronic suspension control module (2) until it is fully seated into the electronic suspension control module bracket (1) and secured by the tab as indicated.
4. Active Safety Control Module@Left Side - Install.
5. Program the electronic suspension control module.
ELECTRONIC SUSPENSION CONTROL MODULE BRACKET REPLACEMENT
.png)
Preliminary Procedure
Electronic Suspension Control Module - Remove.
- Electronic Suspension Control Module Bracket Nut[2x]
CAUTION: Fastener Caution
Tighten 22 N.m (16 lb ft) - Electronic Suspension Control Module Bracket Bolt
Tighten 22 N.m (16 lb ft) - Electronic Suspension Control Module Bracket
FRONT SUSPENSION 4 CORNER LEVELING SYSTEM POSITION SENSOR REPLACEMENT
Removal Procedure
1. Remove the front tire and wheel assembly. 2.
.png)
Separate the front suspension 4 corner leveling system position sensor harness clip (1) from the sensor bracket (2).
3.
.png)
Electrical Connector(1)@Front Suspension 4 Corner Leveling System Position Sensor (2) - Disconnect.
4.
.png)
Link Rod (1)@Ball Stud (2) - Disconnect.
5.
.png)
Front Suspension 4 Corner Leveling System Position Sensor Bracket Nut (1) - Remove.
6.
.png)
Front Suspension 4 Corner Leveling System Position Sensor (1) - Remove.
Installation
1.
.png)
Front Suspension 4 Corner Leveling System Position Sensor (1) - Install.
2.
.png)
CAUTION: Refer to Fastener Caution.
Front Suspension 4 Corner Leveling System Position Sensor Bracket Nut (1) - Install and tighten 9 N.m (80 lb in).
3.
.png)
Link Rod (1)@Ball Stud (2) - Connect.
4.
.png)
Electrical Connector(1)@Front Suspension 4 Corner Leveling System Position Sensor (2) - Connect.
5.
.png)
Install the front suspension 4 corner leveling system position sensor harness clip (1) to the sensor bracket (2).
6. Install the front tire and wheel assembly.
READ NEXT:
Rear Suspension 4 Corner Air Leveling Position Sensor Replacement (CNQ)
Removal Procedure
1. Remove the rear tire and wheel assembly.
2. Separate the rear suspension 4 corner air leveling position sensor harness
clip from the underbody
rear side rail.
3. Electrical Co
Description and Operation
ELECTRONIC SUSPENSION CONTROL DESCRIPTION AND OPERATION
K19 - K19 Suspension Control Module
B161LF - B161LF Vertical Suspension Acceleration Sensor - Left Front
B161RF - B161RF Vertical Suspension Ac
Front Suspension
Specifications
FASTENER SPECIFICATIONS
Single Use Threaded Fastener/Component Tightening Specifications
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced
with NEW
aft
SEE MORE:
Engine Oil Life System
When to Change Engine Oil
This vehicle has a computer system
that indicates when to change the
engine oil and filter. This is based
on a combination of factors which
include engine revolutions, engine
temperature, and miles driven.
Based on driving conditions, the
mileage at which an oil change is
Cylinder Head Disassembly
NOTE: Examples used in this article are general in nature and do not
necessarily
relate to a specific engine or system. Illustrations and procedures have
been chosen to guide mechanic through engine overhaul process.
Descriptions of processes of cleaning, inspection, assembly and machine
shop prac
