Buick Regal: Adjust Link Replacement (FWD)
Removal Procedure
1. Remove the tire and wheel assembly.
2. Rear Wheel Speed Sensor Replacement (Front Wheel Drive) Rear Wheel Speed Sensor Replacement (All Wheel Drive) - Remove.
3.
Rear Suspension Adjust Link Nut(1) - Remove.
4. Rear Suspension Adjust Link Cam(2) - Remove.
5.
Rear Suspension Adjust Link Inner Bolt(1) - Remove.
DISCARD the bolt.
6.
Rear Suspension Adjust Link Outer Nut(1) - Remove.
7. Remove the rear suspension outer bolt (2) and washer (3).
DISCARD the bolt.
8.
Rear Suspension Adjust Link(1) - Remove.
Installation Procedure
1.
Rear Suspension Adjust Link(1) - Install.
2.
CAUTION: This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component.
Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.
Rear Suspension Adjust Link Inner Bolt(1) - Install.
Install a NEW bolt.
3.
CAUTION: Refer to Fastener Caution.
Rear Suspension Adjust Link Cam(2) - Install.
4. Rear Suspension Adjust Link Nut(1) - Install and tighten 90 N.m (66 lb ft).
5.
Install the rear suspension adjust link outer bolt (2) and washer (3).
Install a NEW bolt.
6. Rear Suspension Adjust Link Outer Nut(1) - Install.
Tighten
- First Pass: 160 N.m (118 lb ft)
- Final Pass: (90 - 105 degrees)
7. Check the rear wheel alignment.
ADJUST LINK REPLACEMENT (AWD)
Removal Procedure
1. Remove the tire and wheel assembly.
2.
Rear Wheel Speed Sensor Harness(1)@Rear Suspension Adjust Link(2) - Separate.
3.
Remove the rear suspension adjust link outer bolt (1) and washer (2).
DISCARD the bolt.
4.
Rear Suspension Adjust Link Nut(1) - Remove.
5. Rear Suspension Adjust Link Cam(2) - Remove.
6. Rear Suspension Adjust Link Inner Bolt - (3) Remove.
7.
Rear Suspension Adjust Link(1) - Remove.
Installation Procedure
1.
Rear Suspension Adjust Link(1) - Install.
2.
CAUTION: Refer to Fastener Caution.
Rear Suspension Adjust Link Inner Bolt(3) - Install.
3. Rear Suspension Adjust Link Cam(2) - Install.
4. Rear Suspension Adjust Link Nut(1) - Install.
Tighten
- First Pass: 80 N.m (59 lb ft)
- Final Pass: (30 - 45 degrees)
5.
Install a NEW rear suspension adjust link bolt (1) and washer (2).
Tighten
CAUTION: This vehicle is equipped with torque-to-yield or single use fasteners.
Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.
- First Pass: 100 N.m (74 lb ft)
- Final Pass: (90-105 degrees)
6.
Rear Wheel Speed Sensor Harness(1)@Rear Suspension Adjust Link(2) - Install.
7. Check the rear toe adjustment.
READ NEXT:
Rear Spring Replacement (FWD)
Removal Procedure
1. Remove the rear tire and wheel assembly.
2.
Rear Stabilizer Shaft Link Nut(1) - Remove.
3. Rear Stabilizer Shaft Link Bolt(2) - Remove.
4.
Rear Shock Absorber Nut(1) - Remove
Rear Suspension Upper Lateral Link Replacement (FWD)
Removal Procedure
1. Remove the tire and wheel assembly.
2. { If equipped }Rear Suspension Position Ball Socket @Rear Suspension Upper
Lateral Link - Disconnect.
3.
Rear Suspension Upper Lateral Li
Rear Suspension Lower Trailing Link Replacement
Removal Procedure
1. Raise and support the vehicle.
2. Remove the rear tire and wheel assembly.
3.
Rear Suspension Trailing Arm Nut(1) - Remove.
4. Rear Suspension Trailing Arm Bolt(2) - Remove a
SEE MORE:
Speedometer
The speedometer shows the
vehicle's speed in either kilometers
per hour (km/h) or miles per
hour (mph).
Odometer
The odometer shows how far the
vehicle has been driven, in either
kilometers or miles.
Tachometer
The tachometer displays the engine
speed in revolutions per
minute (rpm).
For vehicles w
Setting Cruise Control
If is on when not in use, SET-
or
RES+ could get pressed and go into
cruise when not desired. Keep
off when cruise is not being used.
1. Press to turn the cruise
system on.
2. Get to the speed desired.
3. Press and release SET- . The
desired set speed briefly
appears in the instrument
cluster
