Buick Regal Owners & Service Manuals

Buick Regal: DTC C0035-C0051 (RPO J69)

Diagnostic Instructions

  • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
  • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
  • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC C0035

Left Front Wheel Speed Sensor Circuit

DTC C0036

Left Front Wheel Speed Sensor Range Performance

DTC C003A

Front Wheel Speed Sensor Circuit

DTC C0040

Right Front Wheel Speed Sensor Circuit

DTC C0041

Right Front Wheel Speed Sensor Range Performance

DTC C0045

Left Rear Wheel Speed Sensor Circuit

DTC C0046

Left Rear Wheel Speed Sensor Range Performance

DTC C0050

Right Rear Wheel Speed Sensor Circuit

DTC C0051

Right Rear Wheel Speed Sensor Range Performance

For symptom byte information refer to Symptom Byte List

Diagnostic Fault Information

Antilock Brake System

Antilock Brake System

Antilock Brake System

Circuit/System Description

Each wheel speed sensor receives ignition voltage through the signal high circuit from the electronic brake control module. Wheel speeds are detected by active wheel speed sensors and encoder rings. The magnetic encoder rings consists of multiple north and south pole pairs surrounding the outer circumference. When the encoder ring rotates and passes by the wheel speed sensor; it generates a sign wave in the wheel speed sensor. The sensor converts the signal to a digital square wave; the square wave values switch between 7mA (Low) and 14mA (High) DC current. As the wheel spins, the module uses the frequency of the square wave signal to calculate the wheel speed.

Conditions for Running the DTC

C0035 00 - C0050 00 C0035 01 - C0050 01, C0035 02 - C0050 02, C0035 05 - C0050 05, C0035 06 - C0050 06, C0035 18 - C0050 18, or C0035 27 - C0050 27

Ignition ON

C0035 0F - C0050 0F or C0035 5A - C0050 5A

Vehicle speed is greater than 60 km/h (37 MPH).

Conditions for Setting the DTC

C0035 00 - C0050 00 C0035 01 - C0050 01, C0035 02 - C0050 02, C0035 05 - C0050 05, C0035 06 - C0050 06

  • A short to ground, or open/high resistance on the wheel speed sensor signal high circuit is detected for 0.2 sec.
  • A short to voltage, short to ground, or open/high resistance on the wheel speed sensor signal low circuit is detected for 0.2 sec.

C0035 18, C0040 18, C0045 18, or C0050 18

  • An erratic wheel speed sensor signal is detected.

C0035 0F, C0040 0F, C0045 0F, or C0050 0F

  • Incorrectly mounted wheel speed sensor.
  • Debris on the wheel speed sensor or the tone ring.
  • Missing tooth or teeth on the wheel speed sensor tone ring.
  • Air gap between the wheel speed sensor and the encoder ring.
  • Electrical magnetic interference with the wheel speed sensor harness.

C0035 27, C0040 27, C0045 27, or C0050 27

  • Debris on the wheel speed sensor tone ring.
  • Missing tooth or teeth on the wheel speed sensor tone ring.
  • Air gap between the wheel speed sensor and the encoder ring too large.

C0035 67, C0040 67, C0045 67, or C0050 67

  • An incorrect part wheel speed sensor signal is detected.

Action Taken When the DTC Sets

  • The ABS indicator turns ON.
  • The traction/stability control indicator turns ON.
  • A driver information center message may be displayed.
  • The electronic brake control module disables the ABS, the traction control, and the electronic stability program for the duration of the ignition cycle.

Conditions for Clearing the DTC

  • When the condition for setting the DTC is no longer present.
  • The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.

Diagnostic Aids

  • Do not use a magnet to clean the encoder ring.
  • Inspect the wheel encoder ring for rust or corrosion.
  • Inspect the wheel speed sensors and components for the correct parts.
  • If two or more wheel speed sensors are inoperative, diagnose each wheel speed sensor individually.
  • If symptom code 0F, 27, or 5A is set, refer to the Diagnostic Fault Information table for possible mechanical faults or conditions.
  • If the customer comments that the ABS indicator is ON only during moist environmental conditions (rain, snow, vehicle wash, etc.), inspect the wheel speed sensor wiring for signs of water intrusion.

Reference Information

Schematic Reference

Antilock Brake System Wiring Schematics

Connector End View Reference

Component Connector End View Index

Description and Operation

ABS Description and Operation

Electrical Information Reference

  • Circuit Testing
  • Connector Repairs
  • Testing for Intermittent Conditions and Poor Connections
  • Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

1. Drive the vehicle in a straight line at a speed greater than 40 km/h (25 MPH).

2. Verify all scan tool Wheel Speed Sensor parameters are within 1.6 km/h (1 MPH) of each other.

  • If any parameter is not within 1.6 km/h (1 MPH) of each other.

Refer to Circuit/System Testing.

  • Go to next step: If each parameter is within 1.6 km/h (1 MPH) of each other.

3. All OK.

Circuit/System Testing

1. Inspect the appropriate B5 Wheel Speed Sensor and encoder ring for contamination, metallic particles, physical damage, incorrect installation and the correct component.

  • If contamination, physical damage, incorrect installation, or the wrong component is diagnosed

Repair or replace the applicable component.

  • Go to next step: If no contamination, physical damage, incorrect installation, or the wrong component is not diagnosed

2. Ignition OFF and all vehicle systems OFF, disconnect the harness connectors at the appropriate B5 Wheel Speed Sensor and the harness connector at the K17 Electronic Brake Control Module, ignition ON.

3. Test for less than 1 V between the K17 Electronic Brake Control Module harness connector terminals listed below and ground:

  • B5LF Wheel Speed Sensor - Left Front - terminal 8 and terminal 19
  • B5LR Wheel Speed Sensor - Left Rear - terminal 18 and terminal 31
  • B5RF Wheel Speed Sensor - Right Front - terminal 4 and terminal 16
  • B5RR Wheel Speed Sensor - Right Rear - terminal 29 and terminal 17
  • If 1 V or greater

Repair the short to voltage on the circuit.

  • Go to next step: If less than 1 V

4. Ignition OFF.

5. Test for infinite resistance between the K17 Electronic Brake Control Module harness connector terminals listed below and ground:

  • B5LF Wheel Speed Sensor - Left Front - terminal 8 and terminal 19
  • B5LR Wheel Speed Sensor - Left Rear - terminal 18 and terminal 31
  • B5RF Wheel Speed Sensor - Right Front - terminal 4 and terminal 16
  • B5RR Wheel Speed Sensor - Right Rear - terminal 29 and terminal 17
  • If less than infinite resistance

Repair the short to ground on the circuit.

  • Go to next step: If infinite resistance

6. Test for less than 2 Ω between the B5 Wheel Speed Sensor harness connector terminal 1 and the K17 Electronic Brake Control Module harness connector terminal listed below:

  • B5LF Wheel Speed Sensor - Left Front - terminal 19
  • B5LR Wheel Speed Sensor - Left Rear - terminal 31
  • B5RF Wheel Speed Sensor - Right Front - terminal 16
  • B5RR Wheel Speed Sensor - Right Rear - terminal 17
  • If 2 Ω or greater

Repair the open/high resistance in the circuit.

  • Go to next step: If less than 2 Ω

7. Test for less than 2 Ω between the B5 Wheel Speed Sensor harness connector terminal 2 and the K17 Electronic Brake Control Module harness connector terminal listed below:

  • B5LF Wheel Speed Sensor - Left Front - terminal 8
  • B5LR Wheel Speed Sensor - Left Rear - terminal 18
  • B5RF Wheel Speed Sensor - Right Front - terminal 4
  • B5RR Wheel Speed Sensor - Right Rear - terminal 29
  • If 2 Ω or greater

Repair the open/high resistance in the circuit.

  • Go to next step: If less than 2 Ω

8. Replace the B5 Wheel Speed Sensor.

9. Verify the DTC does not set while operating the vehicle within Conditions for Running the DTC.

  • If the DTC sets

Replace the K17 Electronic Brake Control Module.

  • Go to next step: If the DTC does not set

10. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

  • Front Wheel Speed Sensor Replacement
  • Rear Wheel Speed Sensor Replacement (Front Wheel Drive) or Rear Wheel Speed Sensor Replacement (All Wheel Drive)
  • Control Module References for electronic brake control module replacement, programming and setup

    READ NEXT:

     DTC C0035-C0051 (RPO J71)

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC C0055

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

     DTC C0110

    Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diag

    SEE MORE:

     Intake Manifold Installation

    Special Tools EN-45059 Angle Meter EN-50790 HP Fuel Pump Installation Alignment Gauge For equivalent regional tools, refer to Special Tools. 1. Install a NEW gasket (1) on the intake manifold (3). Install the intake manifold and hand start the intake manifold bolts (2, 4). 2. CAUTION: Refer

     Vehicle, Engine and Transmission ID and VIN Location, Derivative and Usage

    The vehicle identification number (VIN) plate is the legal identifier of the vehicle. The VIN plate is located on the upper left corner of the instrument panel (I/P) and can be seen through the windshield from the outside of the vehicle: 2.0L (LTG) Engine ID and VIN Derivative Location Engine I

    © 2019-2024 Copyright www.buregal6.com