Buick Regal: Inside Air Temperature Sensor Replacement - Left Side Upper
1. Instrument Panel Assembly - Remove.
2. Temperature Valve Actuator - Left Side - Remove.
3. Mode Control Cam Actuator - Remove.
4. Mode Control Cam Actuator Mounting Plate - Remove.
5.
.png)
Mode Valve Lever(1) - Remove.
6.
.png)
Mode Control Cam(1) - Remove.
7.
.png)
Inside Air Temperature Sensor - Left Side Upper(1) - Remove.
8. Unlock the retaining tabs.
9. Disconnect the electrical connector.(2).
Installation Procedure
1.
.png)
Inside Air Temperature Sensor - Left Side Upper(1) - Install.
2. Connect the electrical connector.(2).
3.
.png)
Mode Control Cam(1) - Install.
4. Lubricate the mode control cam in order to assure proper operation.
5.
.png)
Mode Valve Lever(1) - Install.
6. Lubricate the mode valve lever in order to assure proper operation.
7. Mode Control Cam Actuator Mounting Plate - Install.
8. Mode Control Cam Actuator - Install.
9. Temperature Valve Actuator - Left Side - Install.
10. Instrument Panel Assembly - Install.
INSIDE AIR TEMPERATURE SENSOR REPLACEMENT - LEFT SIDE LOWER
.png)
Preliminary Procedure: Floor Front Air Outlet Duct Replacement - Left Side Â.
- Inside Air Temperature Sensor - Left Side Lower
Procedure- Disconnect the electrical connector.
- Unlock the retaining tabs.
INSIDE AIR TEMPERATURE SENSOR REPLACEMENT - RIGHT SIDE UPPER
.png)
Preliminary Procedure
Instrument Panel Compartment Replacement.
- Inside Air Temperature Sensor - Right Side Upper
Procedure- Disconnect the electrical connector.
- Unlock the retaining tabs.
INSIDE AIR TEMPERATURE SENSOR REPLACEMENT - RIGHT SIDE LOWER
.png)
Preliminary Procedure
Instrument Panel Compartment Replacement.
- Inside Air Temperature Sensor - Right Side Lower
Procedure- Disconnect the electrical connector.
- Unlock the retaining tabs.
INSIDE AIR MOISTURE AND WINDSHIELD TEMPERATURE SENSOR REPLACEMENT
.png)
Preliminary Procedure
Inside Rearview Mirror Replacement.
- Inside Air Moisture and Windshield Temperature Sensor Retainer
Procedure
Unlock the retaining tabs. - Inside Air Moisture and Windshield Temperature Sensor
Procedure
Disconnect the electrical connector.
SUN LOAD TEMPERATURE AND HEADLAMP AUTOMATIC CONTROL AMBIENT LIGHT SENSOR REPLACEMENT
.png)
Preliminary Procedure
Radio Front Speaker Grille Replacement.
- Sun Load Temperature and Headlamp Automatic Control Ambient Light Sensor
READ NEXT:
Description and Operation
AUTOMATIC HVAC DESCRIPTION AND OPERATION
The air temperature and the air delivery description and operation are
divided into eight areas:
HVAC Control Components
Air Speed
Air Delivery
Heating a
HVAC - Manual
SPECIFICATIONS
FASTENER SPECIFICATIONS
Reusable Threaded Fastener Tightening Specifications
NOTE:
All fasteners listed in this table can be reused after removal.
REPAIR INSTRUCTIONS
HEATER AND AIR CO
Seat Belts
SCHEMATIC WIRING DIAGRAMS
SEAT BELT WIRING SCHEMATICS
Seat Belts
SEE MORE:
Vent Hose Replacement
Removal Procedure
1. Raise and support the vehicle. Lifting and Jacking the Vehicle.
2.
Transmission Vent Hose (1) @Transmission - Disconnect.
3. Lower the vehicle.
4.
Unclip the vent hose retainer (2) from the radiator surge tank (3).
NOTE: Note the routing of the vent hose.
5. Transmission Ve
Fuel Injector Circuit Diagnosis
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
Diagnostic Procedure Instructions provides an overview of each
diagnostic category.
Diagnostic Fault
