Buick Regal Owners & Service Manuals
Buick Regal 2018-2024 Service Manual / Brakes / Park Brake / Repair Instructions / Parking Brake Actuator Replacement (GNQ)

Buick Regal: Parking Brake Actuator Replacement (GNQ)

Removal Procedure

WARNING: Brake Dust Warning

1. Set the park brake in Service Mode.

Manual Method

  1. Change the transmission gear to neutral or park position.
  2. Press and hold the push button start switch for 10 seconds, with the brake pedal not applied.

    This will place the vehicle in Service Mode (Ignition ON with the engine OFF).

  3. Press brake pedal several times until brake booster vacuum is empty.
  4. Press the brake pedal and press the park brake switch until the orange park brake lamp begins to flash. By keeping the brake pedal applied, release and re-press the park brake switch for approximately 5 seconds.
  5. Release the brake pedal. The orange park brake lamp extinguishes for a moment after which the rear brake calipers are retracting.

Scan Tool Method (only use if manual method fails)

  1. Install the scan tool to the vehicle and perform the rear brake caliper piston retract.

2. Raise and support the vehicle.

3. Remove the tire and wheel assembly.

4.

Park Brake

Rear Parking Brake Actuator Electrical Connector (1) - Disconnect.

5.

Park Brake

Rear Parking Brake Actuator Harness Retainer (1) - Release.

6.

Park Brake

Rear Parking Brake Actuator Bolt (1) - Remove[2x].

7.

Park Brake

Wire Bracket (1) - Remove.

8.

Park Brake

Rear Parking Brake Actuator(1) - Remove.

9.

Park Brake

Rear Parking Brake ActuatorSeal(1) - Remove and DISCARD.

Installation Procedure

1.

Park Brake

Rear Parking Brake ActuatorSeal(1) - Install NEW.

2.

Park Brake

Rear Parking Brake Actuator(1) - Install.

3.

Park Brake

Wire Bracket (1) - Install.

4.

Park Brake

CAUTION: Fastener Caution

Rear Parking Brake Actuator Bolt (1) - Install and tighten 12 N.m (106 lb in)[2x].

5.

Park Brake

Rear Parking Brake Actuator Harness Retainer (1) - Secure.

6.

Park Brake

Rear Parking Brake Actuator Electrical Connector (1) - Connect.

7. Install the tire and wheel assembly.

8. Reset the park brake system from Service Mode.

Manual Method

  1. Change the transmission gear to neutral or park position.
  2. Press and hold the push button start switch for 10 seconds, with the brake pedal not applied.

    This will place the vehicle in Service Mode (Ignition ON with the engine OFF).

  3. Press the brake pedal and pull the park brake switch until the orange park brake lamp extinguishes and the rear brake calipers are extending.
  4. Release the brake pedal.

Scan Tool Method (only use if manual method fails)

  1. Install the scan tool to the vehicle and perform the rear brake caliper piston extend.

PARKING BRAKE SERVICE MODE SELECTION

Rear Parking Brake Actuator Release - Service Mode

Prior to any rear disc brake or parking brake service, the parking brake actuator must be placed in Service Mode.

  1. Install a scan tool to the vehicle.
  2. Turn the ignition ON with the engine OFF.
  3. On the scan tool menu, select Electronic Brake Control Module.
  4. Select Control Functions.

NOTE: Do NOT apply any brake pedal pressure during this step.

  1. Select Rear Brake Caliper Piston Retract.
  2. After the repair is complete, calibrate the park brake. Park Brake Calibration

Rear Parking Brake Actuator Release - Manual Release

In the event the rear parking brake actuator fails or there is a loss of electrical power, the parking brake may be released manually.

  1. Remove the rear parking brake actuator. Rear Parking Brake Actuator Replacement.
  2. Insert an appropriate hex tool past the splines of the parking brake actuator piston apply spindle in the brake caliper.
  3. Rotate the parking brake actuator piston apply spindle clockwise to release the parking brake.
  4. After the repair is complete, calibrate the park brake.

    READ NEXT:

     Description and Operation

    ELECTRONIC PARKING BRAKE DESCRIPTION Vehicles with the electric parking brake have a switch in the center console or on the dash, which takes the place of the manual parking brake system, the foot pe

     Suspension

    Buick Wheel Alignment Specifications WHEEL ALIGNMENT SPECIFICATIONS REGAL GNC 225/55 R17 REGAL GNC 245/40 R19 REGAL GNC 245/45 R18 REGAL GNQ 225/55 R17 REGAL GNQ 245/40 R19 REGAL GNQ 245/45 R18

     Electronic Suspension Control

    SPECIFICATIONS FASTENER SPECIFICATIONS Reusable Threaded Fastener Tightening Specifications NOTE: All fasteners listed in this table can be reused after removal. SCHEMATIC AND WIRING DIAGRAMS ELECTRO

    SEE MORE:

     Camshaft Timing Chain and Tensioner Replacement

    Removal Procedure 1. Remove the engine front cover. Refer to Engine Front Cover Replacement. 2. Remove the upper timing chain guide bolts (2, 3). 3. Remove the upper timing chain guide (1). 4. Timing Chain Tensioner Bolt (1) - Remove [2x]. 5. Timing Chain Tensioner (2) - Remove. 6. Timing Cha

     DTC P0798, P0970, or P0971

    Diagnostic Instructions Perform the Diagnostic System Check prior to using this diagnostic procedure: Refer to Diagnostic System Check - Vehicle Review the description of Strategy Based Diagnosis: Refer to Strategy Based Diagnosis An overview of each diagnostic category can be found here: R

    © 2019-2024 Copyright www.buregal6.com