Buick Regal: Rear Differential Clutch Control Module Replacement
Removal Procedure
1. Prepare the control module for removal using the SPS programming support tool.
NOTE: The rear differential clutch control module can now be removed and replaced.
2. Raise and support the vehicle.
3. Differential Carrier Assembly - Drain.
4. Propeller Shaft - Remove.
5. Exhaust Muffler Assembly - Remove.
6. Rear Parking Brake Actuator - Disconnect.
7. Rear Wheel Drive Shaft - Remove.
8. Differential Carrier Assembly - Remove.
9.
.png)
Rear Differential Clutch Control Module Bolt(1) - Remove.
10.
.png)
Disconnect the connectors from the rear differential clutch control module (1 - 3).
11.
.png)
Rear Differential Clutch Control Module Wiring Harness(1) - Remove.
12.
.png)
Rear Differential Clutch Control Module(1) - Remove.
Installation Procedure
1.
.png)
Rear Differential Clutch Control Module(1) - Install.
2.
.png)
Rear Differential Clutch Control Module Wiring Harness(1) - Install.
3.
.png)
Reconnect the connectors from the rear differential clutch control module (1 - 3).
4.
.png)
CAUTION: Refer to Fastener Caution.
Rear Differential Clutch Control Module Bolt(1) - Install and tighten6 N.m (53 lb in).
5. Differential Carrier Assembly - Install.
6. Remove the hydraulic jack.
7. Rear Wheel Drive Shaft - Install.
8. Rear Parking Brake Actuator - Connect.
9. Exhaust Muffler Assembly - Install.
10. Propeller Shaft - Install.
11. Remove the supports and lower the vehicle.
12. Program the rear differential control module.
REAR AXLE LUBRICANT LEVEL INSPECTION
1. Raise and support the vehicle.
2. Clean the area around the rear axle fill plug.
3. Place a drain pan under the vehicle.
4.
.png)
Rear Axle Housing Fill Plug(1) - Remove.
5. Rear Axle Housing Filler Plug Gasket(2) - Remove.
6. Check the fluid level. If necessary, fill the differential to the bottom of the fill plug hole with the recommended fluid.
CAUTION: Refer to Component Fastener Tightening Caution.
NOTE: Clean and inspect the filler plug gasket (2) and replace if necessary.
7. Rear Axle Housing Filler Plug Gasket(2) - Install.
8. Rear Axle Housing Fill Plug(1) - Install and tighten 25 N.m (18 lb ft).
9. Lower the vehicle.
READ NEXT:
Differential Clutch Oil Inspection
1. Raise and support the vehicle.
2. Clean the area around the rear axle fill plug.
3. Place a drain pan under the vehicle.
4.
Differential Clutch Cover Plug(1) - Remove.
5. Rear Axle Housing Fi
Differential Carrier Bushing Replacement - Rear
Tools Required
J-45725 Cradle Bushing Replacer
For equivalent regional tool, refer to Special Tools.
Removal Procedure
1. Raise and support the vehicle.
2. Remove the rear differential assembly.
3
Rear Axle Vent Replacement
Preliminary Procedure
1. Raise and support the vehicle.
2. Remove the Differential Carrier Assembly.
Rear Axle Vent
NOTE:
Use an appropriate tool to remove and install.
REAR AXLE HOUSING VENT
SEE MORE:
Distracted Driving
Distraction comes in many forms
and can take your focus from the
task of driving. Exercise good
judgment and do not let other
activities divert your attention away
from the road. Many local
governments have enacted laws
regarding driver distraction. Become
familiar with the local laws in
your area.
DTC P1400
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this
diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic
approach.
Diagnostic Procedure Instructions provide an overview of each diagnostic
category.
DTC Descriptor
DTC
